Installing a pool table may seem inconvenient, but it's actually quite simple. During installation, you only need to understand the methods and patterns involved, and you can easily assemble the pool table!
　　I. Leg Differentiation
　　When purchasing a pool table, the packaging crates for the pool table legs will total three boxes (each box contains two legs)
　　Open the packaging box of the pool table legs. You will find that the two sides of the upper part of the legs each have three small holes perpendicular to a straight line. The middle hole is for threading screws, and the two on the sides are for inserting wooden dowels.
　　II. Installation Method for Long and Short Boards
　　Side A is the insertion point for the long board, and Side B is the insertion point for the short board. Following the above steps, the lower part of the pool table is basically assembled!
　　Installation Method for Remaining Parts
　　1. Leveling the Slate
　　After installing the iron frame of the next part of the pool table, the iron frame must be centered and marked. Then, lay the slate in the appropriate position on the marked lines. Because the slate is assembled from three boards, the two seams in the middle may be uneven, which is normal. Next, we need to level the slate. The material we need to prepare during the leveling process is playing cards; playing cards are the best and most professional leveling method. Using playing cards, pad the lower part of the slate to make the two seams level (Note: While making the seams level, we must also ensure that the entire slate surface is level).
　　2. Laying the Cloth
　　After the slate is leveled, we must lay the cloth. When laying the cloth on the slate surface, the only requirement is to lay it tightly, making the table surface very flat. To lay the cloth, simply use special adhesive to attach the edges of the cloth to the sides of the slate.
　　3. Installation of the Upper Rail
　　After the cloth is installed, the upper rail can be installed immediately. In addition, the iron corners must be inserted into the sockets on both sides of the upper rail. Tighten the screws to keep the upper rail level, and then tighten the screws.
　　4. Installation of Other Small Parts
　　Before explaining the installation of the pocket opening, let's first understand the different types of pool table accessories that make up the pocket opening: leather mouth, arc-shaped iron corner, net pocket, and channel. These parts are consumables and easily damaged parts. If you are opening a pool hall, then you must study these carefully to avoid the trouble of having to replace the pocket opening later.
　　How to assemble a pool table most conveniently?
　　Assembly of the Pool Pocket Opening
　　Simply put, it is to assemble the leather mouth, arc-shaped iron corner, net pocket, and channel together. The key materials for assembling them are: shoelaces, and wire.
　　1. Wrap the Iron Mouth with the Leather Mouth
　　If you have a leather mouth on hand, you can observe that there will be a row of neat small holes on both sides of the leather mouth. These holes are for convenient fastening during assembly. Then, tightly wrap the leather mouth around the iron mouth.
　　2. Hook the Net Pocket Long Side with Shoelaces
　　Before hooking the net pocket, we must first observe that the structure of the net pocket is long on one side and short on the other. The long side is used to hook onto the edge of the leather mouth, and the short side is used to hook the wire to the selected wood.
　　Hook the long side of the net pocket to the edge of the leather mouth using shoelaces.
　　3. Hook the Net Pocket Long Side with Wire
　　The self-made wire should be arc-shaped, and about 30 cm in length is fine. Make the ends of the wire round for easy tightening of the screws later.
　　Wrap the wire and the long side of the net pocket together.
　　4. Installation of the Channel
　　First, understand the appearance of the pool table channel; one end has a golden yellow circle, and the other end has a dark gray strap.
　　Fasten the end of the channel with the metal ring to the end of the net pocket with the circle. During installation, gently pinch the circle on the net pocket slightly flat, then slant it and fasten it into the metal ring of the channel, and after fastening, return the flattened circle on the net pocket to its original shape.
　　Then, secure the other end of the channel with the strap to the bottom of the upper rail.